MAKE YOUR OWN DIY TORO TIMEMASTER DRAG FLAP THAT LASTS

#Toro #Timemaster #DIY
MAKE YOUR OWN DIY TORO TIMEMASTER DRAG FLAP THAT LASTS. Toro definitely cut corners on this part of the Timemaster mower. The first drag flap lasted only 25 hours. The new one only lasted 4 hours. And I'm not spending another dime on a Toro brand drag flap. They just don't last. Watch and see how I make my own! LIKE and SUBSCRIBE!

CONTACT INFO:
[email protected] (I am currently out of flaps. I will remove this message if I have more come in. See my ALTERNATIVE MODIFICATION below. Thank you for your interest.)
Instagram - Garagegearjb

WATCH THESE NEXT:

Toro Timemaster Quick Fix - This Part Only Lasted 25 Hours.
https://youtu.be/vPZXPQTAsNc

Mow Longer - Modify Your Toro Timemaster With A 1 Gallon Fuel Tank
https://youtu.be/t6a37qNx7m4

Stripe Your Lawn With The Toro Timemaster Striping Kit - Tested And Reviewed
https://youtu.be/Dv6n9ZCWAHE

Installing A Striping Kit On My Toro TimeMaster Lawnmower
https://youtu.be/D-w202RhcaU

PRODUCT LINKS:

John Deere Original Equipment Shield #M112900 (you will need 2 of these)
https://amzn.to/3hYc172

Metal 5/16 Rod
https://amzn.to/3klWw9l

Lock Nuts
https://amzn.to/3fAqFyi

Rubber Sheet You Could Use To Make Your Own Drag Flap
https://amzn.to/31nSlRL

Wilton Vise
https://amzn.to/31p4kP8

Hacksaw
https://amzn.to/3kg7UDH

File Set
https://amzn.to/33vxAGA

DeWalt Drill Driver Combo Set
https://amzn.to/33uiC3D

Toro Timemaster Lawnmower
https://amzn.to/2C3Ozo9

Pittsburgh 225 Piece Socket Set
https://amzn.to/2PANlUh

Box Cutting Knife
https://amzn.to/3gAqAf4

Measuring Tape
https://amzn.to/31nhCeU

****ALTERNATE MODIFICATION****

Use 2 of these Honda rubber flaps. Trim them to fit left to right. You may also have to cut a little off of the length as they may be a little too long. https://amzn.to/3dWjDoA

You may need a thinner rod to run across the bottom of the time master. I am not sure of the diameter of the thread hole on the Honda flaps. You could check at Home Depot for the right diameter size. A 36" length will be needed.

This 3/16 Threaded Rod may fit. https://amzn.to/3uFHcsK

3/16 Lock Nuts https://amzn.to/3a144eg

Disclaimer:
Due to factors beyond the control of Garage Gear, I cannot guarantee against improper use or unauthorized modifications of this information. Garage Gear assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Garage Gear recommends safe practices when working on machines and or with tools seen or implied in this video. Due to factors beyond the control of Garage Gear, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Garage Gear.

JB from Garage Gear is a member of the Amazon Affiliate Program.