Toyota Programming Keyless Remote 2 DIFFERENT PROCEDURES √

Repair Manuals: https://shrsl.com/3zwnv https://sovrn.co/amfaf3n Fix it Angel EBAY STORE: https://ebay.us/OE6UsK repair smith https://fxo.co/1284793/fixitangel THANK YOU ALL FOR WATCHING MY VIDEO. This video is NOT sponsored. If you would like to support this channel. These links are my affiliate links which means if you buy something I will receive a small commission. Thank you for your support. God Bless
https://www.amazon.com/shop/fixitangel https://www.getsomevegas.com/home
Going to Vegas? Check out deals here!!
https://goo.gl/ghgxZc

Please donate here if this video was helpful
Click LINK https://www.paypal.me/FixItAngel

Check out my online store for tools to purchase
https://www.amazon.com/shop/fixitangel
Amazon Prime Membership https://goo.gl/AvLVjs

Purchase any of my apparel and a portion of my monthly earnings will go to Catholic Charities here in Las Vegas
Click LINK http://www.cafepress.com/fixitangel

You can also follow me in:
Facebook https://www.facebook.com/fixitangel328
Twitter https://twitter.com/FixItAngel
Instagram https://www.instagram.com/fixitangel/

When I was employed at a Toyota Dealer, from 2005-2012, the service foreman gave us techs these 2 written procedures to program keyless remotes on LATE and EARLY model cars.

The first procedure is the more commonly used. Second is for earlier models. TRY BOTH PROCEDURES TO SEE IF IT WORKS ON YOUR CAR.

Procedure for LATE models: (MORE COMMON)

Start with drivers door open, and all other doors closed.

Insert key into ignition and remove it 2 times

Close and open drivers door 2 times

Insert key into ignition and remove it 1 time

Close and open drivers door 2 times

Insert key into ignition

Close drivers door

Cycle key from lock to on 1 time, then remove key from ignition

Wait for door locks to cycle 1 time

Press lock and unlock buttons on remote at the same time, then press lock button on remote

Wait for door locks to cycle 1 time

Insert key into ignition, and cycle on then off once

Get out of vehicle, close door and test operation

If door locks do not cycle, or cycle twice. Then restart procedure

EARLY model procedure:

Drivers door open all others closed, key out of ignition

Insert key into ignition and remove it 1 time

Cycle door locks with power lock button from lock to unlock
5 times

Close and open drivers door 1 time

Cycle door locks with power lock button from lock to unlock
5 times

Insert key into ignition and cycle from off to on 1 time

Wait for door locks to cycle 1 time

Press lock and unlock buttons on remote at the same time and release

Press lock button on the remote 1 time

Wait for door locks to cycle

Insert key into ignition and cycle from off to on 1 time

Exit vehicle and test system

The information contained in this video is for general guidance, not responsible for any errors or injuries that you have done. IPhone 5 was used to do this video. DISCLAIMER - Due to factors beyond the control of FixitAngel, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. FixitAngel assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. FixitAngel recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of FixitAngel, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the end user and not FixitAngel nor any of it’s subsidiaries. All links in the description are affiliate links. if you would like to support this channel. purchase any of the product links. i get a little commission from each purchase. thank you