How to Remove the Cab Light on a Dodge Ram

How to remove and replace the bulbs in the center mount cab light on a third generation Dodge Ram 1500. This is a 2006 model, however a similar process can be applied to other models as well. #eManualOnline #dodgeram #dodgetrucks

eManualOnline: bit.ly/3BTq3lp
20% Discount Code: 4DIYERS20

Amazon affiliated links:
US:
Rear center high mount light (PN: 5072594AD): https://amzn.to/3IMIcFl
Rear center high mount light harness (PN: 5072577AA): https://amzn.to/41k6IVp
912 incandescent replacement bulbs: https://amzn.to/3ZimRsR
Auxbeam LED 912 light upgrade: https://amzn.to/3ImXsXR
Canada:
Rear center high mount light (PN: 5072594AD): https://amzn.to/3xL05xV
Rear center high mount light harness (PN: 5072577AA): https://amzn.to/3kdMQTq
912 incandescent replacement bulbs: https://amzn.to/3KDA5vQ
Auxbeam LED 912 light upgrade: https://amzn.to/3Zdh07T

Website: http://4diyers.com
Patreon: https://www.patreon.com/4diyers
Facebook: https://www.facebook.com/4diyers
Twitter: https://twitter.com/4DIYers
Instagram: https://www.instagram.com/4diyers/
Tumblr: http://4diyers.tumblr.com
Pintrest: https://www.pinterest.com/4diyers/

Tools/Supplies Needed:
-phillips screwdriver
-replacement light bulbs

Procedure:
Using a phillips screwdriver, remove the two screws on each side of the light assembly. There will be two small nylon washers, don’t lose these.

The bulbs can be twisted counterclockwise and pulled out of their location while everything is in place.

Or you have the option of pushing in the tab on the white connector, then pulling the connection apart.

I prefer removing the connector as it’s easier to clean the gasket and sealing surface around the assembly to ensure we have no water leaks after reinstallation.

Clean the area around the light, this should be done otherwise this can potentially cause a water leak.

Once the light is out, here is the assembly. As you can see there are two cargo lights, one on each side. Then the third brake light is in the center.

These bulbs as shown earlier simply twist out of their location for removal. Twist counterclockwise and pull straight out.

If you are required to troubleshoot any electrical problems relating to this lighting circuit or any other specific areas, I would recommend checking out eManualOnline for dealer specific repair manuals. These are available in a PDF format so you can put this on your phone or laptop, being able to work right beside your vehicle and determine what exactly is wrong. These will allow you to save money using proper diagnostic procedures, pinpointing what exactly needs to be done for a repair. As you can see scrolling through the manual for my truck, there are detailed wiring diagrams, diagnostic procedures and removal steps just for this lighting circuit. eManualOnline has hooked me up with a 20% discount code for site wide, it’s 4DIYERS20, make sure you also use my referral link in the video description, this will allow me to make a percentage for each sale to help keep my channel going.

To replace the bulbs, they simply pull out of their location, then the new bulbs are pushed into place.

The connector is then reinstalled back into the assembly.

Plug the electrical connector back into place, then install the light.

Make sure it’s in place, before installing the screws I did test out the light to ensure it’s working correctly.

Then the screws are installed.

Many people ask me where I get my torque values for fasteners, I get them from manuals as I mentioned earlier. So for these screws, the torque specifications are 20 inch pounds or 2 NM.

Thank you to all those who watch my videos and support my content. Don't forget to subscribe to my channel for future tutorial videos and like my video if you found it helpful. New videos are always being uploaded every week!

© 4DIYers 2013
All Rights Reserved
No part of this video or any of its contents may be reproduced, copied, modified or adapted, without the prior written consent of the author.