⚠ Easy Test - 3D Printer Calibration - Extruder Calibration Calculator - E Steps Calculator

⚠ Easy Test - 3D Printer Calibration - Extruder Calibration Calculator - E Steps Calculator

🔴 Subscribe to my channel: https://www.youtube.com/@3DParts4U
🎁 My Patreon page: https://www.patreon.com/3DParts4U
🎧 My Spotify playlists: https://open.spotify.com/user/schipperrene?si=06d90570db5f48f6

A quick 3D printer extruder calibration test!
See if your printer pushes out enough, too much or too little filament.

Send the following 3-line G-code to your 3D printer (SD card or USB drive):

>>

T0 ; Select left extruder
M109 S180 ; Set temperature and wait for left extruder
G1 E100 F150

<<

G1: a linear movement
E100: an extrusion of 100mm length of filament
F150: speed is 150mm per minute

👉 More about G-codes: https://marlinfw.org/docs/gcode/G000-G001.html
👉 Image used: https://unsplash.com/photos/pAATRR5q30A
👉 Image used: https://unsplash.com/photos/Q1NS-nISNIw

My steps per mm were set on 147 and that was the right number.
What if it wasn't the right number?

I added a marker at 100mm from the inlet and it stopped exactly there.
So it extruded 100mm as intended with the g-code.

What if it stopped 10mm before it? Then it extruded 100-10 = 90mm instead of 100mm.
The steps per mm (E-steps) should be 147*100 = 14700 / 90 = 163,3 instead of 147.

Repeat the steps above until 100mm length of filament is extruded after sending the code.

⏱ Chapters:
0:01 Extruder calibration
1:33 Channel promo (https://www.youtube.com/@allvisuals4u)
1:38 Website promo (https://www.3dpartsforyou.com)

👍 Thanks for watching the video Easy Test - 3D Printer Calibration - Extruder Calibration Calculator - E Steps Calculator

🌐 Visit my website: https://www.3dpartsforyou.com

🔩 Subscribe to my other channel AllVisuals4U | Design & Engineering: https://www.youtube.com/@AllVisuals4U
🔩 All playlists of AllVisuals4U | Design & Engineering: https://www.youtube.com/@AllVisuals4U/playlists

📦 Subscribe to my channel 3DParts4U | 3D Printing For Everyone: https://www.youtube.com/@3dparts4u
📦 All playlists of 3DParts4U | 3D Printing For Everyone: https://www.youtube.com/@3dparts4u/playlists

⚡ Subscribe to my short format channel: https://www.youtube.com/@AllVisuals4UShorts
⚡ All playlists of the short format channel: https://www.youtube.com/@AllVisuals4UShorts/playlists

#3DParts4U #AllVisuals4U #3DPrinted #3DPrinting #3DPrints #3DPrint #3DPrinter
#3DPrintedModels #3DModel #PLA #3DDesign #Maker #Making #Modeling #Filament #Tutorial #Tutorials #HowTo #Wiki #Manual #Help #Tips #Tricks #Calibration #ExtruderCalibration #Calculator #ESteps

🔈 Nu Disco Funk by WinnieTheMoog
Free download: https://filmmusic.io/song/6169-nu-disco-funk
Licensed under CC BY 4.0: https://filmmusic.io/standard-license